Painless Plans For Drain cleaning repairs - An Inside View

Excellent Plumbing Solutions That Anyone Can Do

Plumbing does not have to be as complicated as most people make it out to be. There are some basic things that you need to know about plumbing systems, as well as, having the necessary tools to do your own repairs. This article may have a few useful tips and tricks that you can add to your tool belt.

Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. Flux retards oxidation when the copper is heated. Always use lead-free or nearly lead-free solder when sweating a copper joint.

Certain things shouldn't go into your plumbing system. By knowing what you can and cannot flush or throw into the garbage disposal and sink, you can save yourself from a costly repair or disaster. A plumber can usually get your plumbing back into working condition, but can be avoided if you know how to dispose of items correctly.

If you have noisy pipes, you can cushion them with a rubber blanket or add additional anchor straps. Banging pipes are usually caused by loose pipes, water hammering to a stop as you turn it off, or hot water pipes shifting in their position. All of these problems can be solved by cushioning and anchoring the pipes.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Use your garbage disposal with the cold water running so that you can preserve the blades of the disposal. Using hot water makes grease more liquid and can cause problems, including clogs. Make sure to clean blades by putting in a little dish detergent and run cold water at the same time.

There are simple ways to check your toilet for leaks that can ultimately lead to great cost savings in the long read more run. The easiest way to do this is to pour a small amount of food dye into the holding tank of your toilet overnight. In the morning, if you have any color in the basin then you know you have a leak that needs some attention.

Do not forget to check the temperature of the water heater in your house, especially if you are planning to leave for an extended period of time. You should keep the temperature no higher than 120 degrees, which will help to reduce energy use and prevent your system from burning out.

Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of all, remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up the other end of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.

If you have problems with a slow drain, there are easier things you can do other than removing the pipes to clean it. There are certain tools made just for this purpose that you insert into the drain to loosen the clog so it washes away or grab it and remove it completely.

If you think you understand what is wrong with your toilet, but aren't sure, you should first do some more research on the internet. Most plumbing problems are fairly standard, and you should be able to read about the problem in great detail on several amateur plumber forums to make sure you understand the problem.

In the winter months, if you live somewhere where temperatures fall below freezing, leave your faucets on a little bit to let a thin stream of water through. This will help prevent the pipes from freezing, which could be a major problem for you and all the pipes in your home.

When plunging a drain to attempt to remove a blockage, first make sure that the drain is completely covered in water. This helps to form a seal. Then, plunge at least fifteen to twenty times before stopping. Repeat the process two to three times. If this doesn't work, try a chemical drain cleaner.

In conclusion, there is a lot that you can easily do in your own home when it comes to dealing with plumbing issues. Hopefully you learned a few things and will be able to act on them. Use this advice today and be confident in all of the plumbing work that you do.

How to get a decent plumber without going round the U-bend

Finding the valves

You can also search for reputable tradesmen in England and Wales via the Association of Plumbing and Heating Contractors (APHC) and in Scotland and Northern Ireland through SNIPEF.

John Thompson, the chief executive of the APHC, says there really is no need to stick with the first available plumber that you stumble on.

"If you feel pressurised into accepting work without a full explanation, have the confidence to question or get a second opinion. Also check if the tradesmen has the right credentials to work on your appliances," he says.

Mind you, if water is pouring, or even just dripping from the ceiling, you will need to try and isolate the problems to minimise damage before the plumber arrives.

For major leaks, turn off the water supply at the main stop tap, usually in the kitchen. You might need to resort to turning off the water company tap at the boundary of the property. Older ones may also turn off your neighbour's supply.

Smaller internal leaks can be stopped using local isolation valves - usually next to the appliance or tap concerned. These may be less familiar to older consumers as they take the form of levers or are just turned with a screwdriver.

On a combi boiler the isolation valve will be located underneath the boiler.

Ian Ruddick

Image caption,

Turning the thermostat up too suddenly can push your boiler over the edge, says Ian Puddick

Lagging

Ian Puddick is the founder of the London Boiler Company. His team is well used to being called out to replace worn out boilers which give up the ghost when they are pushed too hard.

"What happens is that all of a sudden people turn the thermostat up, but this pushes your boiler over the edge," he says.

"Also where you have tanks in the loft, check the little one to see that it's full of water. These can work with little in them for years, but when you turn the temperature up it drives the system a bit harder and then it stops."

Mr Puddick also has a helpful tip for avoiding a big freeze in your loft.

"Once you have checked all your pipes and tanks are lagged, protected and covered, check underneath the water tank. If there's some insulation there just pull it out and leave that area clear so heat can rise and protect the tank."

Emergency repairs are costly. So to avoid being fleeced by an opportunist plumber, it's worth getting your pipes and systems checked and serviced by a reputable engineer before temperatures drop once again.